The Auto Parts Trade Toolkit

汽配外贸工具箱 · 六大换算工具

Six free calculators for auto parts and hardware exporters — torque, wire gauge, threads, units, CBM and metal weight. Everything runs locally in your browser. No account needed to use it — sign up to save results in your own notebook.

汽配、五金外贸一站式小工具:全部在本地浏览器计算,不用注册登录;结果可存进记录本,免费版存本机、云端版跨设备同步。

Built for sales · purchasing · QC · engineers Offline ready Metric ⇄ Imperial

Torque Converter扭矩换算 · N·m / lb-ft / lb-in / kgf·m

US drawings and service manuals state torque in lb-ft or lb-in; Asian and European specs use N·m or kgf·m. Type a value in any box — the rest update instantly.

美国图纸和维修手册常用 lb-ft / lb-in,亚洲和欧洲规格用 N·m / kgf·m。任意一个框里输入数值,其余单位实时联动。

Quick set (lb-ft)快捷取值:

Reference only. Always follow the torque spec printed on the drawing, service manual or fastener datasheet — values here are converted, not recommended.仅供参考:以图纸、维修手册或紧固件资料上的扭矩值为准,这里只做换算,不做推荐。

How to use it使用方法

  • Type the number you already have — the row you type in stays untouched.输入你手上已有的那个数值,正在输入的框不会被改动。
  • Decimals and negative values are accepted; comma is read as a decimal point.支持小数和负数,逗号会当作小数点。
  • Use “Copy all values” to paste every unit at once into an email or spec sheet.点「复制全部」可一次把各单位的数值粘进邮件或规格表。

FAQ常见问题

Is lb-ft the same as ft-lb?和 ft-lb 是一回事吗

People say “ft-lb” but the correct unit is lb-ft (pound-force × foot). Same number, same meaning — this tool uses lb-ft.口语常说 ft-lb,规范写法是 lb-ft(磅力 × 英尺),数值和含义一样,本工具统一用 lb-ft。

Why is 1 N·m equal to 0.7376 lb-ft?为什么 1 N·m = 0.7376 lb-ft

1 lb-ft = 1 lbf × 1 ft = 4.44822 N × 0.3048 m = 1.35582 N·m. So 1 N·m = 1 / 1.35582 = 0.73756 lb-ft.1 lb-ft = 1 lbf × 1 ft = 4.44822 N × 0.3048 m = 1.35582 N·m,所以 1 N·m = 1 / 1.35582 = 0.73756 lb-ft。

Which unit do US offroad customers expect?美国越野客户习惯看哪个单位

lb-ft for chassis, suspension and wheel torque; lb-in for small fasteners under 20 lb-ft. Metric customers expect N·m.底盘、悬挂、轮毂用 lb-ft;20 lb-ft 以下小紧固件用 lb-in;公制客户看 N·m。

Common conversions常用换算

lb-ftN·mlb-inkgf·m

AWG Wire Gauge Chart美制线规 · AWG ⇄ mm² ⇄ inch ⇄ mm

American Wire Gauge (AWG) is the standard for US electrical and harness wiring. Convert between AWG, cross-section (mm²) and conductor diameter, and check copper resistance per 1000 ft / 100 m.

美制 AWG 是线束与电缆配线的通用标准。可在 AWG、截面积 mm²、导体直径之间互换,并查铜电阻。

Diameter (inch)直径 inch
—
Cross-section截面积
—mm²
Copper resistance铜电阻
—Ω/1000ft
Copper resistance铜电阻
—Ω/km

Resistance is calculated at 20 °C with ρ = 10.371 Ω·cmil/ft (annealed copper) and is a reference value only; insulation, temperature and strand count change real-world results.电阻按 20 ℃、软铜 ρ = 10.371 Ω·cmil/ft 计算,仅作参考;绝缘、温度、股数都会影响实际值。

Full AWG table完整 AWG 表

AWGDiameter (in)直径Diameter (mm)直径Area (mm²)截面积Copper Ω/1000 ft铜电阻Copper Ω/km铜电阻

Common automotive ranges: 18–22 AWG for signal and low-current wiring, 14–18 AWG for lighting and accessory wiring, 8–12 AWG for main power feeds.车用常见范围:18–22 AWG 信号与弱电流配线,14–18 AWG 灯具与附件配线,8–12 AWG 主电源线。

UNC / UNF Thread Chart美制英制螺纹对照 · TPI · 螺距

Inch fasteners are specified by size and threads per inch. UNC is coarse (general purpose), UNF is fine (vibration and thin-wall applications). Major diameter, TPI and metric pitch below.

美制螺纹按「规格 + 每英寸牙数」表示:UNC 粗牙通用,UNF 细牙抗振、适合薄壁。下表给出大径、TPI 和公制螺距。

Size规格Major dia (in)大径Major dia (mm)大径 UNC TPI牙数UNC pitch (mm)螺距UNF TPI牙数UNF pitch (mm)螺距
Swipe the table sideways on a phone to read the UNF columns.

Click any row (or pick a size in the card above) and the card explains that thread instantly — major diameter, TPI, metric pitch and the clearance hole to drill. Major diameter is the largest diameter of the external thread; verify against your customer’s drawing before production.点表格任意一行(或在上方卡片选规格)即可看到大径、TPI、公制螺距和建议过孔孔径。大径是外螺纹的最大直径,量产前请对照客户图纸复核。

Selected thread · 当前规格
—

FAQ常见问题

What does 1/4-20 UNC mean?1/4-20 UNC 是什么意思

1/4 inch nominal major diameter, 20 threads per inch, coarse series. 20 TPI = 1.27 mm pitch (25.4 / 20).1/4 英寸公称大径,每英寸 20 牙,粗牙系列;20 TPI 对应螺距 25.4 ÷ 20 = 1.27 mm。

How do I convert TPI to metric pitch?TPI 怎么换算成公制螺距

Pitch (mm) = 25.4 / TPI. A 13 TPI thread equals 1.954 mm pitch — close to, but not interchangeable with, M12 × 1.75.螺距 mm = 25.4 ÷ TPI。13 TPI 等于 1.954 mm,接近 M12×1.75,但不能互换。

UNC or UNF for general hardware?一般五金件用 UNC 还是 UNF

Fine threads (UNF) hold preload better under vibration but gall more easily in dirty environments; most brackets use UNC for robustness and faster assembly.细牙 UNF 在振动下保持预紧力更好,但脏环境下容易咬死;多数支架用 UNC,更结实、装配更快。

How to use it使用方法

  • Pick a size in the card (or click a table row) — the diagram and the numbers follow the selection, nothing else to click.在卡片里选规格(或点表格某行),图形和参数会跟着变,不用再点别处。
  • “Highlight common hardware” marks sizes typically found on brackets, studs and general hardware.「高亮常用件」会标出支架、螺柱等常规五金件的常用规格。
  • Switch UNC / UNF in the card to compare coarse and fine pitch on the same size.在卡片里切 UNC / UNF,可对比同一规格的粗牙与细牙。

Clearance hole rule of thumb: add 0.5–1.0 mm over major diameter for a free fit, 0.2–0.4 mm for a close fit — verify with the mating part.过孔经验值:松配在大径上加 0.5–1.0 mm,紧配加 0.2–0.4 mm,最好用实物配件验证。

Unit Converter通用单位换算 · 长度 / 重量 / 压力 / 温度 / 功率 / 体积

The conversions that show up on every auto parts spec sheet and quotation. Pick a group, type in any box.

报价单和规格书上最常见的换算:选一个类别,任意框输入即可。

US gallon (3.785 L) and UK gallon (4.546 L) are different — always confirm which one a quotation refers to. Bar, psi and kPa all appear on pneumatic and tire specs.美制加仑 3.785 L 与英制加仑 4.546 L 不同,报价时务必确认用哪一个;bar、psi、kPa 都会出现在气压与轮胎规格中。

Handy references常用参数

Pressure压力

1 bar = 14.5038 psi = 100 kPa. Tire pressure charts in the US use psi; EU tire labels use bar or kPa.1 bar = 14.5038 psi = 100 kPa。美国轮胎气压表用 psi,欧洲标签用 bar 或 kPa。

Power功率

1 mechanical HP (US) = 745.7 W; 1 metric PS = 735.5 W. A “100 HP” US rating is 1.4 % higher than 100 PS.1 美制马力 HP = 745.7 W,1 公制马力 PS = 735.5 W;同样标 100,美国 HP 比欧洲 PS 高 1.4%。

Length长度

1 inch = 25.4 mm exactly. 1 ft = 12 in = 304.8 mm. Fractional inches (e.g. 3/8 in) are common on US drawings.1 inch = 25.4 mm(精确值),1 ft = 12 in = 304.8 mm;美国图纸常用分数英寸,如 3/8 in。

Common traps常见误区

  • Ounce: 1 oz = 28.3495 g (avoirdupois), not fluid ounce.盎司:1 oz = 28.3495 g(常衡),不是液体盎司。
  • Ton: US short ton 907.18 kg, metric tonne 1000 kg, UK long ton 1016.05 kg.吨:美制短吨 907.18 kg,公吨 1000 kg,英制长吨 1016.05 kg。
  • Temperature: convert temperatures, not temperature differences — a 10 °C rise equals an 18 °F rise.温度:换的是温度值而非温差,升温 10 ℃ 等于升温 18 ℉。
  • Volume: US gal 3.785 L vs UK gal 4.546 L — a 17 % difference on the same label.体积:美制加仑 3.785 L,英制加仑 4.546 L,同样的标签相差 17%。

CBM & Chargeable Weight Calculator装箱体积 · 多包装分行计算 · 合计汇总

Add one row per carton size, set quantity and weight per carton — total CBM, volumetric weight and container fill are summed automatically.

每个包装尺寸加一行,填数量和每箱重量,合计体积、体积重、柜量占比自动汇总。

Branded packing list品牌装箱单抬头(可选,只存本机)

Saved in this browser only — no upload. 仅保存在本机浏览器,不会上传任何数据。

#序L长W宽H高Qty数量kg / ctn箱重CBM
Swipe the table sideways on a phone to reach the CBM and delete columns.
Total CBM合计体积
—
Air volumetric weight体积重
—kg (1:167)
Actual gross weight实际毛重
—kg
Packages / cartons箱数
—
Container fill estimate柜量占比
—
H L W
L × W × H of the outer carton. Measure the box, not the product — pallet overhang and tube packing change the real volume.填纸箱的外长 × 宽 × 高,量箱子而不是量产品;托盘外扩、圆管包装都会改变实际体积。

Container volumes are typical usable loading space, not the nominal capacity: 20GP ≈ 28 CBM, 40GP ≈ 58 CBM, 40HQ ≈ 68 CBM. Actual fill depends on carton stacking and pallet use.柜容为常用可装体积,非名义容积:20GP≈28 CBM、40GP≈58 CBM、40HQ≈68 CBM,实际装载取决于堆码与托盘。

Formulas计算公式

CBM体积 CBM

Length × width × height in metres = CBM per carton; multiply by carton quantity for the total.长 × 宽 × 高(米)= 每箱 CBM,再乘以箱数得合计。

Air volumetric weight体积重

1 CBM = 167 kg (standard air freight divisor 6000): chargeable weight = the greater of actual weight and volumetric weight.1 CBM = 167 kg(空运标准除数 6000),计费重取实重与体积重中的较大者。

Sea LCL海运拼箱

LCL is charged per CBM or per 1000 kg (W/M), whichever is greater — compare your total CBM with gross weight in tonnes.拼箱按 CBM 或按 1000 kg(W/M)计费,取较大者;把合计 CBM 与毛重吨数比一下就知道按哪个算。

Tips提示

  • Measure the outer carton size, not the product.量纸箱外尺寸,不要量产品尺寸。
  • Add 1–2 cm per side for pallet overhang when the forwarder charges by pallet footprint.货代按托盘占地面积计费时,每边留 1–2 cm 托盘外扩。
  • Long items (poles, profiles, tubes) often ship by tube — confirm the forwarder’s oversize rule before quoting.长件(杆类、型材、管材)常走圆管包装,报价前先确认货代的超长规则。
  • Use “+ Add package” for each carton size; every row is totalled into the summary below.每种箱规用「+ 添加包装」加一行,所有行都会汇总到下方结果。

Metal Weight Calculator材料重量估算 · 管 / 棒 / 板 / 型材

Weight per piece, per metre and per order — for aluminum tube, stainless bar, steel plate or brass flat.

单件、每米、整单重量估算,适用于铝管、不锈钢棒、钢板、黄铜扁料。

Weight per piece单件
—kg
Weight per metre每米
—kg/m
Total weight总重
—kg
Total weight总重
—lb

Theoretical weight from nominal dimensions and density. Real mill weight varies ±3–10 % with tolerance, and surface treatment adds weight.按公称尺寸与密度算出的理论重量,实际过磅会因公差浮动 ±3–10 %,表面处理还会加重。

Formulas计算公式

Round tube圆管

(OD − t) × t × π × ρ / 1000 = kg per metre, OD and t in mm, ρ in g/cm³.(外径 − 壁厚)× 壁厚 × π × 密度 ÷ 1000 = 每米公斤数,尺寸用 mm,密度用 g/cm³。

Square / rectangular tube方矩管

2 × (A + B − 2t) × t × ρ / 1000 = kg per metre.2 ×(A + B − 2×壁厚)× 壁厚 × 密度 ÷ 1000 = 每米公斤数。

Plate板材

1 m² plate weighs thickness (mm) × ρ. A 3 mm carbon steel sheet is 23.6 kg/m².1 m² 板重 = 厚度 mm × 密度;3 mm 碳钢板约 23.6 kg/m²。

Density reference材料密度

  • Carbon steel 7.85 · 304 7.93 · 316 7.98 g/cm³碳钢 7.85 · 304 7.93 · 316 7.98 g/cm³
  • Aluminum 6061 2.70 · 6063 2.68 · 7075 2.81 g/cm³铝 6061 2.70 · 6063 2.68 · 7075 2.81 g/cm³
  • Brass 8.50 · copper 8.96 g/cm³黄铜 8.50 · 紫铜 8.96 g/cm³

Selecting a material fills its density automatically. Choose “Custom” to type your own value.选材质会自动填入密度;选「自定义」可手动输入密度值。